When you looking for ramps board 1.4, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable ramps board 1.4 is not an easy task. In this post, we show you how to find the right ramps board 1.4 along with our top-rated reviews. Please check out our suggestions to find the best ramps board 1.4 for you.
Reviews
1. KINGPRINT 3D Printer MKS Gen V1.4 Controller Board Mega 2560 R3 Motherboard RepRap Ramps1.4 Compatible with USB
Feature
Mega 2560 and ramps1.4 set on a board, to solve complicated Ramps1.4 combination of interfaces, the problem of failure prone.Replace the motor drive, drive and support 4988 8825 drive.
The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
Using high-quality MOSFET, and better heat dissipation.
Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
Description
-Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.-Tthe firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.
- Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can't be sure to match all of stype of 12864LCD and 2004LCD )
- Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
-Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.
Specification
Type: MKS Gen V1.4 control board Mega 2560
Name: MKS Gen V1.4 control board
Weight: 118g
Application: 3D Printer Part
Weight: 118g
Package Included:
1* MKS Gen V1.4 Control Board
2. KEYESTUDIO 3D Printer Controller RAMPS 1.4 for Arduino REPRAP MENDEL PRUSA
Feature
It is a Mega Pololu Shield, or RAMPS for short, designed to fit the entire electronics needed for a RepRap in one small package for low cost.RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion.
Has provisions for the cartesian robot and extruder.
Expandable to control other accessories.
3 mosfets for heater / fan outputs and 3 thermistor circuits.
Description
IntroductionIt is a Mega Pololu Shield, or RAMPS for short, designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful
Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy
service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top
of the stack.
Specification
1. Has provisions for the cartesian robot and extruder;
2. Expandable to control other accessories;
3. 3 mosfets for heater / fan outputs and 3 thermistor circuits;
4. Fused at 5A for additional safety and component protection;
5. Heated bed control with additional 11A fuse;
6. Fits 5 Pololu stepper driver board;
7. Pololu boards are on pin header sockets so they can be replaced easily or removed for use in future designs;
8. I2C and SPI pins left available for future expansion;
9. All the Mosfets are hooked into PWM pins for versatility;
10. Servo style connectors are used to connect to the endstops, motors, and LEDs. These connectors are gold plated, rated for 3A, very compact;
11. SD Card add on available
12. LEDs indicate when heater outputs on
13. Option to connect 2 motors to Z for Prusa Mendel
3. HiLetgo RAMPS 1.4 Control Panel 3D Printer Control Board Reprap Control Board Support Arduino Mega 2560
Feature
The fifth stepper motor output port can be customized as a Z-axis motor or a second extruder.Can be extended to control other accessories.
Three field effect transistors, three heater / fan output ports, three thermistor circuits.
Heated bed control, extra 11A fuse.
Pololu board foot socket, can be easily replaced or removed.
Description
Description:RepRap Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
Features
1.It has Cartesian robots and regulations of the extruder .
2.Extended to control other accessories.
3.Heater / MOSFET outputs and three fan thermistor circuit.
4.Integration of additional security 5A and component protection.
5.Control of additional heating bed 11A fuse.
6.Suitable for 5 Pololu stepper driver board.
7.Pololu board pin socket, so they can be easily replaced or removed for future designs.
8.I2C and SPI pins left for future expansion.
9.Hooked into all MOSFET PWM pin versatility.
10.Servo type connector is used to connect to the end stop , the motor and the light-emitting diodes. These connectors are gold-plated , rated current of 3A, very compact.
11.On the SD card to add - is now available from the Kliment - Sdramps.
12.LED indicate when the heater output.
13.Option 2 motors connected to Z Prusa Mendel.
Package Included
1* RAMPS 1.4 Control Panel 3D Printer Control Board Reprap Control Board
4. OSOYOO 3D Printer Kit with RAMPS 1.4 Controller + Mega 2560 board + 5pcs A4988 Stepper Motor Driver with Heatsink + LCD 12864 Graphic Smart Display Controller with Adapter For Arduino RepRap
Feature
3D printer Kit guide: 3D printer Kit guide: http://osoyoo.com/driver/3D%20printer%20instructions.pdf3D Printer Controller RAMPS 1.4 interfaces an Arduino Mega2560 board. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino-compatible MEGA shield for easy service, part replacement, upgrade-ability and expansion
With LCD 12864, you can easy connect it to your Ramps board using the "smart adapter" included. After connecting this panel to your Ramps you don't need your pc any more, the Smart Controller supplies power for your SD card. Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD card.
It is designed to fit the entire electronics needed for a RepRap in one small package for low cost
We are professional factory on making all electronics components based on Arduino and Raspberry Pi. And we also have processional engineer team to offer you tutorials which you can start from beginning. all documents (including code)
Description
3D printer Kit guide: http://osoyoo.com/driver/3D%20printer%20instructions.pdf
Caution:
1) The max power supply for these ramps is 12V and the max watts is about 180W. The max watts for the hotbed is about 100W and the max temperature is just 50 degree Celsius.
2) Do not plug or unplug and wire or module when power is on, do not even touch the board when power is on or your hand has static charge(you can remove static charge by touching metal tap) .
3) Always double check power wire is properly installed. If you do not follow above move, you may damage the control board and your 3D printer.
4) Pls confirm the A4988 driver install correctly on Ramps1.4 board.
5) The endstop pins are Signal-GND-VCC, instead of VCC-Signal-GND like the rest of RepRaps boards. Make sure to wire them correctly. This is done to allow squeezing fatter traces on the printable board.
6) Don't secure Arduino/Ramps with conductive screws through both mounting holes. The screw may cut into the positive trace creating a HIGH current short.
7) Test all electronics thoroughly before placing into service.
8) Do not leave power supplied to electronics unattended, or run machines unattended due to the risk of fire and malfunction.
9) Once you start putting electricity into your RepRap - even at just 12 volts - you have to take basic, common sense precautions to avoid fires. Just in case these fail. test your workshop smoke detector.
Product Specification:
1) Marlin firmware update: Arduino IDE 1.5.X
2) This kit consists of a RAMPS 1.4 shield, an Mega 2560 board, five Stepper drivers and a LCD. It can control up to 5 stepper motors with 1/16 stepping precision and interface
5. Wangdd22 3D Printer Controller for RAMPS 1.4 REPRAP MENDEL PRUSA for Arduino 3D Printe Accessories
Feature
Suitable for 5 Pololu stepper driver boardIntegrated 5A extra safety and components protection
I2C and SPI pin for extended use
Rated current: 3A
LED indicates when the heater output
Description
Description:RepRap Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Ard Mega with the powerful Ard MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Ard MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Ard expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack. Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
Features:
With rules of cartesian coordinate robot and extruder.
Could control spare parts.
With heater/fan output/three thermistor MOSFET.
Integrated 5A extra safety and components protection.
Suit for 5 Pololu stepper driver plate.
Pololu plate pin socket.
I2C/SPI pin for future development.
All MOSFET with PWM pins.
Servo connector used to connect end dog, motor and lighting diode. Rated current 3A.
SD card add Kliment-Sdramps.
LED indicates heater output.
Two motor connects to Z Prusa Mendal.
Package included:
1 x 3D Printer Controller for Arduino RAMPS 1.4 REPRAP MENDEL PRUSA for Arduino
6. KINGPRINT Mega 2560 R3 Board + LCD12864 + Ramps 1.4 + 5pcs DRV8825 Stepper Motor Driver Module with Heat Sink for 3d printer
Feature
MEGA2560 R3- This version is optimized in the original version , mainly for customers under the functional requirements for product quality and high case designed both to ensure consistent and compatible with the original, but also easy to use.RAMPS 1.4- Suitable for 5 Pololu stepper driver board, integrated 5A extra safety and components protection.
DRV8825-Features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step)
12864LCD- Suitable for copiers, fax machines, laser printers, industrial test equipment, networking equipment etc. LCD control panel through which you can achieve spooling is the 3D model Gcode files are copied to the SD card, and then print the file via the LCD control panel.
Do not worry about the problem of after-sales, if there is any need, get in touch with us, we will help you solve it
Description
Specification:Mega 2560 Controller:
-The board is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator
-Development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works
Ramps 1.4:
-Heater / fan output and 3 thermistor circuit MOSFET
-Heating bed control 11A fuse additional
-Servo type connector for connecting to a terminal block, a motor and a light emitting diode
DRV8825:
-It uses 8.2 - 45 V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling)
12864LCD:
-Using a large screen 12864LCD (3.2'), it can support 8 GB
-With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing, product comes encoder parameter adjustment can be achieved
NOTE:
1. Only connect the mega2560 board with the computer via USB cable while programming firmware.
2. Reversed connection of the power supply or the motor driver may cause the board burning, please confirm again before power on.
3. You just need to power Ramps 1.4 when testing.If you power Mega 2560, the chip will be burnt easily. So please read the introduction carefully and avoid the board being burnt due to the wrong operation.
4. Select the appropriate load according to the board voltage/current requirement, if the work current exceeds the load of the board which may cause the board burning
Package Included:
1x Mega 2560 R3
1x LCD 12864
1x Ramps 1.4
5xDRV8825
1x USB Cable
7. BIQU Mega2560 Control Board + LCD 12864 Graphic Smart Display Controller Module + Ramps 1.4 Mega Shield+A4988 Stepstick Stepper Motor Driver with Heat Sink for 3D Printer Arduino Reprap
Feature
LCD12864 is an rotary encoder and a 128 x 64 dot matrix LCD display, full graphic Smart Controller contains a SD-Card reader.Further more all actions like calibration, axes movements can be done by just using the rotary encoder on the Smart Controller. Print your 3D designs without PC, just with a g-code design stored on the SD cardMega 2560 R3,with this product , you are able to use all the Arduino open source platform to create or learn interactive objects
RAMPS 1.4 is designed to fit the entire electronics needed for a RepRap in one small package for low cost
RAMPS interfaces an Arduino-compatible Mega with the powerful Arduino-compatible MEGA platform and has plenty room for expansion
A4988 is a complete microstepping motor driver with built in translator for easy operation
Description
Specification:
12864LCD:
>Using a large screen 12864LCD(3.2'), it can support 8 GB
>With a SD card base on back, put slicing file into the SD card and select the file on the LCD, then can be printing
>Product comes encoder parameter adjustment can be achieved, and the file selection print
>Plug and play on the RAMPS, but need to modify the firmware to support
Ramps 1.4:
>It is right angle coordinate robot and provisions of extruder
>Heater / fan output and 3 thermistor circuit MOSFET
>Fusion 5A extra security and component protection
>Heating bed control 11A fuse additional
>Pololu plate pin socket, so they can be easily replaced or removed for future design >I2C and SPI pins left for future expansion
>Servo type connector for connecting to a terminal block, a motor and a light emitting diode
>These connectors plated, rated current is 3A, very compact
>Option 2 motors are connected to the Z Prusa Mendel
Mega 2560 controller:
>The board is an ATmega2560 as core microcontroller development board itself has 54 groups digital I / O input / output terminal (14 groups do PWM outputs), 16 sets of simulation than the input side, group 4 UARTs (hardware serial ports), using the 16 MHz crystal oscillator
>With the bootloader, download the program directly via USB without having to go through other external writer
>Supply part of the optional USB power, or as an external power using the AC-to-DC adapter and battery
>Development IDE interface is based on open-source principles, allows you to free download for use in project work, school teaching, motor control, interactive works
Package List:
1xMeag 2560 R3 Control Board
1xLCD 12864 Controller
1xRamps 1.4 Controller
5xA4988 Stepper Motor Driver with Heat Sink
1X USB Cable
8. Witbot Ramps1.5 Controller Expanding board Upgraded Ramps1.4 for 3D Printer
Feature
Optimized and upgraded based on RAMPS1.4Patch-type MOS tube, solve the problem of plug-in MOS tube easy to break, take up a large area, poor heat dissipation
It can be extended to LCD and other parts
Design of Pololu plate pin socket can be easily replaced or removed for future design
Applied to 5 Pololu stepper drive board
Description
Description:
This Ramps1.5 contrpller board is changed the original plug-in MOS tube to patch-type MOS tube in order to solve the problem of plug-in MOS tube easy to break, take up a large area, poor heat dissipation , which can improve the stability and aesthetics of the board. The features of multiple extended interface and replaceable parts make RAMPS1.5 become a control board with powerful upgrade capability and scalable modularity. The controller board can be used when the pins on the back of the board are connected to the Arduino Mega and the front is connected to stepper motor drives
Specification:
1,It can be extended to LCD and other parts.
2,There are heater and fan MOSFET outputs and 3 thermistor interfaces
3,5A additional security and component protection fusion
4,Heated bed controls additional 11A fuses
5,Applied to 5 Pololu stepper drive board
6,Design of Pololu plate pin socket can be easily replaced or removed for future design
7,I2C and SPI pins are available for future expansion
8,Support motor drivers: support A4988 DRV8825 and other motor drivers(support five motor drivers Simultaneously)
9, Power: 12v, 200W
10, Patch MOS tube: B55NF06
Notice:
1, Don't connect the live board or replace the module interface (except SD,USB)
2, Please press the RESET button or turn off button when emergency
Package include:
1 xramps1.5 controller
9. HESAI RAMPS 1.4 Controller Control Panel for Reprap Mendel Prusa 3D Printer Support Arduino Mega 2560 Devlepment Board
Feature
Fully assembled & tested, no soldering requiredDesigned to fit the entire electronics needed for a RepRap in one small package for low cost.
Modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion.
A number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
Description
Description:
RepRap Mega Pololu Shield, or RAMPS for short. It is designed to fit the entire electronics needed for a RepRap in one small package for low cost. RAMPS interfaces an Arduino Mega with the powerful Arduino MEGA platform and has plenty room for expansion. The modular design includes plug in stepper drivers and extruder control electronics on an Arduino MEGA shield for easy service, part replacement, upgrade-ability and expansion. Additionally, a number of Arduino expansion boards can be added to the system as long as the main RAMPS board is kept to the top of the stack.
Version 1.4 uses surface mount capacitors and resistors to further cover edge issue cases.
It has Cartesian robots and regulations of the extruder .
Extended to control other accessories.
Heater / MOSFET outputs and three fan thermistor circuit.
Integration of additional security 5A and component protection
Control of additional heating bed 11A fuse
Suitable for 5 Pololu stepper driver board
Pololu board pin socket, so they can be easily replaced or removed for future designs .
I2C and SPI pins left for future expansion.
Hooked into all MOSFET PWM pin versatility.
Servo type connector is used to connect to the end stop , the motor and the light-emitting diodes. These connectors are gold-plated , rated current of 3A, very compact.
On the SD card to add - is now available from the Kliment - Sdramps
LED indicate when the heater output
Option 2 motors connected to Z Prusa Mendel
Package List:
1x Ramps 1.4 Controller
10. KINGPRINT MKS-Gen V1.4 Controller Board+5PCS DRV8825 stepper motor Mega 2560 motherboard RepRap Ramps1.4 compatible +USB Cable for 3D Printer
Feature
The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4.Reserved for motor pulse and direction output ports for easy plug-in high-current To add a large current (eg 2A, 5A) motor drive circuit.
Reserved Ramps1.4 on Servos, AUX-1, AUX-2 interface that provides three 5V output, three 12V outputs.
The circuit board with high-quality 4-layer, heat and made a special optimization; ramps are 2 shelves.
Can accept 24V input power under the same system can be hot-bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems.
Description
Specification: Can be connected to the control panel and 12864LCD Ramps1.4,2004LCD control panel.(Can't be sure to match all of stype of 12864LCD and 2004LCD )MEGA2560 and RAMPS 1.4 set on a board, to solve complicated RAMPS1.4 combination of interfaces, the problem of failure prone.
Support up to 5 motor driver (A4988 or DRV8825).
Using a dedicated power chip, support 12V-24V power input, the voltage converter chip to solve the heat problem Ramps.
Package Included:
5 * DRV8825S Stepper Motor Driver
1 * MKS-Gen V1.4 Controller Board
1 * USB Cable
5 * Mini Heat Sink
11. BIQU MKS-BASE V1.4 Plate Controller Board for 3D Printer Ramps 1.4
Feature
Using 4982 as a motor drive, and a 4988 performance fairly, but with SOP package, heat dissipation will be betterThe circuit board with high-quality 4-layer, and made a special heat treatment optimization; ramps are 2 shelves
Using a dedicated power supply chip, support 12V-24V power input, the voltage converter chip Ramps solve the heating problem
Could accept 24V input, the same system power can heat the bed current is reduced to 1/4, an effective solution to the hot bed MOS pipe heat problems
The firmware can use open source firmware Marlin, ramps1.4 identical configuration and can directly replace Ramps1.4
Description
Specifications:
A collection of all the functions on a single board to solve the complicated interfaces Ramps1.4 combination, problem-prone fault
Using high-quality MOSFET tube heat better
Control panel and can be connected directly Ramps1.4,2004LCD 12864LCD control panel
Net Weight:80g
Dimension:110*90mm
Note:
Before powering up again confirm whether the positive and negative reversed, if the user is due to reverse power and burn, and we do not guarantee such problems
Do not plug in case of power motor drive easily lead to burn; do not adjust the current in the motor is running. The correct approach is to first disconnect the power, unplug the motor, and then re-power, adjust potentiometer, measure the voltage on the potentiometer until the measured voltage is the same as expected
MKS-BASE is to create customer base for R & D personnel Ramps1.4, Megatronics V2.0 and other open source motherboard problems especially developed to optimize the launch of a product, particularly suitable for mass production 3D printer manufacturers use as the main control board
Give full consideration to the stability, heat dissipation, ease of use issues through continuous printing reliability testing
If special needs can contact the owner with details
Supporting line can refer to: 2PIN, 3PIN, 4PIN
Could be directly connected 2004LCD or 12864LCD (remove the L-shaped adapter plate), due to the open-source design 12864LCD 2004LCD and only standardized EXP1 and EXP2 the PIN port on the horns insertion direction and there is no specific standard, so some non Makerbase production and 2004LCD 12864LCD may be inconsistent data line card port direction, in turn, need to plug to use
Package Included:
1* MKS-Base V1.4 3D Printer Controller Board
1* USB Cable
Note: The socket color is ramdon, please double confirm you do not mind before placing order.