If you looking for l298n driver then you are right place. We are searching for the best l298n driver on the market and analyze these products to provide you the best choice.
Reviews
1. L298N Dual H Bridge Stepper Motor Driver Controller Board Module for Arduino UNO MEGA R3 Mega2560 Duemilanove Nano Robot(Pack of 2) by IFANCY-TECH
Feature
Dual-channel H-bridge driver working mode creates higher working efficiencyTo avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
Chip: L298N
Large capacity filter capacitance,afterflow protection diode, more stable and reliable
Description
Specification:Chip: L298N
Logic voltage: 5V
Logic current: 0mA-36mA
Storage Temperature: -20 to to +135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm
2. Solu Dual H Bridge DC Stepper Motor Drive Controller Board Module L298N for Arduino//L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control & Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560
Feature
About us (Solu), Professional factory of circuit boards, welcome to our store for more choices with best price. What we pursue is your satisfication of our service, not just for our goods.For any reason you are unsatisfied with our product at any time, simply contact support for exchange or refund. we will reply you about any question you ask within 24 hoursUsually, you will get it actually in 9~19 days, If you are in the USA and the item is NOT Fulfilled by Amazon. the item will be sent to you by USPS with shipping information from China. The estimated delivery time offered by Amazon is not the real time. Your patience is highly appreciated. Hope you will receive your item soon and enjoy using it.
High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.L298N as main chip, Low heat,outstanding anti-interference performance.
Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply.
Description
About us (Solu), Professional factory of circuit boards, welcome to our store for more choices with best price. What we pursue is your satisfication of our service, not just for our goods.For any reason you are unsatisfied with our product at any time, simply contact support for exchange or refund. we will reply you about any question you ask within 24 hoursSpecifications :
Double H bridge drive
Chip: L298N (ST NEW)
Logical voltage: 5V
Drive voltage: 5V-35V
Logical current: 0mA-36mA
Drive current: 2A(MAX single bridge)
Max power: 25W
Large capacity filter capacitance,afterflow protection diode, more stable and reliable.
Size:43 x 43 x 26mm
Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply
DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2
When ENB enable IN3 IN4 control OUT3 OUT4
Package Includes :
*1 x L298N Dual H Bridge DC Stepper Motor Drive Controller Board Module
3. WGCD 5 PCS L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper Module for Arduino
Feature
L298N main driving chip, high drive ability, low calorific value, strong anti-interference capability.Dual H bridge DC stepper module, more stable and higher work efficiency.
Size: 43 * 43 * 27 mm/1.69 * 1.49 * 1.06in
With built-in 78M05 to supply power, to avoid the damage of voltage regulator chip, when the driving voltage is greater than 12V, please use the external 5V logic power supply.
Package: 5 pcs L298N motor controller board module
Description
Specification:Name: Dual H bridge motor driver module
Working mode: H bridge driver (dual)
Main control chip: L298N
Logic voltage: 5 v
The driving voltage: 5 v - 35 v
Logic current : 0mA-36mA
Drive current: 2 a (MAX single bridge)
Storage temperature: - 20 C to + 135 C
Max power: 25 w
Weight: 30 g
Size: 43 * 43 * 27 mm
L298N motor controller board module, ideal for Arduino smart car power UNO MEGA R3 Mega2560
Package included:
5 pcs L298N Motor Controller Board Module
4. DC Brush Motor Controller, DROK 16A Dual H-Bridge DC Brushed Motor Driver Board DC 5V-48V 12v 24v 48v High Power Motor Drive Control Smart Car PWM Speed Regulator
Feature
DROK dc brush motor controller operating voltage range is DC 5-48V, rated current is 16A, peak current of each channel is 30A, rated output power of each channel is 192W(12v input), 480W(48v input).Special Point: the motor driver is easy programming and easy control, can control forward and reverse rotation, with strong drive and fast break.
Material: our motor control module uses complete two half-bridge driver chip + low internal resistance of N-channel MOSFET, MOSFET switching losses is to a minimum, which improve power utilization than integrated power chip program.
Caution: in the normal operation, the motor output has no over-current protection. Please do not man-made short-circuit, because the module power current is large. Once short-circuit, has the possibility of burning circuit and tube. Please use low current low-voltage testing in the first wiring test; then connect the larger current and voltage. Due to the bare board module sold, please attention wiring thread insulation and prohibited strong voltage touch on board parts.
Note: it is recommended adding the fuses, as without fuses on the power supply circuit of the motherboard. The reversed connection will cause some of the chip permanent damage.
Description
DROK 12v 24v 48v DC Brush Motor Controller
Parameters:
Output channel: 2-way
Working voltage: 5-48V
Rated current: 16A
Each channel peak current: 30A
Each channel output rated power: (12V power supply)192W; (48V power supply)480W
Control signal voltage:3-5V
Each channel control signal current: 2-10MA
Support PWM frequency range: 2-20K
Support PWM duty ratio range: 0-99%
Min. PWM effective pulse width: 10US
Working temperature:-10-80
Notes:
1. We recommend adding the fuses, as without fuses on the power supply circuit of the motherboard. The reversed connection will cause some of the chip permanent damage.
2. In the normal operation, the motor output has no over-current protection. Please do not man-made short-circuit, because the module power current is large. Once short-circuit, has the possibility of burning circuit and tube. Please use low current low-voltage testing in the first wiring test; then connect the larger current and voltage. Due to the bare board module sold, please attention wiring thread insulation and prohibited strong voltage touch onboard parts.
3. Do not connect the drive motor which has obviously inconsistent voltage, current, power, to avoid the unreasonable damage.
4. When switching between positive and negative rotation, it is better to save buffer time on software control, so as to avoid the impact of powerful reverse electromotive force on the MOS tube on the board and reduce the risk of damage.
Package Includes:
1*DC Brush Motor Controller
5. Aideepen 5pcs 1.5A 2 Way DC Motor Driver Module Speed Dual H-Bridge Replace Stepper L298N
Feature
Use of imported original chip, built-in low on-resistance MOS switchDual H-bridge motor driver, can drive two DC motors or a 4-wire two-phase stepper motor
Dual 1.5A * 2, the peak current to be 2.5A, built-in thermal protection circuit, do not be afraid motor stall burned, automatic recovery after the temperature dropped
Minimal heat, no heat sink, small size, low power consumption, is ideal for battery powered
Small size, light weight, 0 standby current, is the ideal choice for your car model
Description
Description:Motor drive module is ideal for use in battery-powered smart car, toy cars, robots.
Supply voltage 2V ~ 10V, can drive two DC motors or a 4-wire 2-phase stepper motors ,can achieve forward rotation or reverse rotation, it is possible to adjust the rotation speed.
Each can provide continuous current of 1.5A, peak current up to 2.5A, thermal protection and can be automatically restored.
Product parameters:
The module supply voltage 2V-10V.
Signal input voltage 1.8-7V.
Single Operating current 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA).
Built-in common conduction circuit, when the input pin is left floating, the motor does not malfunction.
Built-in thermal protection circuit with hysteresis effects (TSD), without worrying about motor stall.
Product size: 24.7 * 21 * 5mm (length, width, height), ultra-small size.
The mounting hole diameter: 2 mm.
Precautions:
1. Power positive and negative reversed will certainly cause damage to the circuit.
2. Output is shorted to ground or output short circuit, and the motor stall, the chip will heat protection, but in the near or exceeding 10V voltage and peak current is greater than 2.5A situation can also cause chip burned.
Package Included:
5* Motor drive module
6. diymore 5Pcs L298N Dual H Bridge DC Stepper Motor L298N Drive Controller Board Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove Nano Robot
Feature
Low heat, outstanding anti-interference performance.Large capacity filter capacitance, afterflow protection diode, more stable and reliable.
Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25W.
Built-in 78M05, get power from drive power,however, when drive power over12V, please use the external 5v power as power supply.
Description
L298N as main chip, ST corporation production.
Low heat,outstanding anti-interference performance.
High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25W.
Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
Built-in 78M05,get power from drive power,however, when drive power over12V, please use the external 5v power as power supply.
Large capacity filter capacitance,afterflow protection diode, more stable and reliable.
Specification:
Double H bridge drive
Chip: L298N (ST NEW)
Logical voltage: 5V
Drive voltage: 5V-35V
Logical current: 0mA-36mA
Drive current: 2A(MAX single bridge)
Max power: 25W
Size:43 x 43 x 26mm
Net weight: 26g
Package weight:36g
Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply.
DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2.
When ENB enable IN3 IN4 control OUT3 OUT4.
Package Included:
5 x Dual H Bridge DC Stepper Motor Drive Controller Board Module Arduino L298N
7. PChero 2Packs L298N Motor Drive Controller Board Module, Dual H Bridge DC Stepper For Arduino Smart Car Robot
Feature
Package Included - 2pcs L298N Motor Driver Controller Board Modules.Item Size - External size 43*43*27mm / 1.69*1.69*1.06 inch. Drive voltage 5V-35V, high working power to 46V. Large current can reach 3A MAX and continue current is 2A. Power to 25w.(NOTE: To avoid damage, please use an external 5V logic supply when using more than 12V driving voltage.)
High Quality - Use L298N as the main driving chip, so the module has such features as strong driving ability, strong anti-interference and low calorific value. And it also use large-capacity filter capacitor and diode with freewheeling protection function, thereby improve the reliability of module.
High Efficiency - Dual-channel H-bridge design, can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.
Easy of Use - No assembly required. This L298N board comes ready to go. Just wire up motors and power, this thing will work wonders.
Description
Why CHOOSE PChero Motor Drive Controller Board Moduld?Reason 1: Use L298N for Main Chip
L298N is a kind of high voltage, high current motor driver chip. Having 15 pins as package, this chip has such features as high working voltage(maximum voltage up to 46V),large output current(instantaneous peak current up to 3A, continuous working current 2A) and 25W of rated power. Two built-in H birdge high voltage and large current full bridge drivers can be used to drive the DC motor and stepper motor, relay coil and so on.Using standard logic level signal control, it has two enable control ends. It permits or prohibites device having a logic power supply input without the impact of input signal, which enables the internal logic circuit part works at low voltage. The chip can connects to external detecting resistor to give the variations to the control circuit. Using L298N chip to drive the motor, this chip can drive a stepping motor or four phase stepping motor, and two DC motors as well.
Reason 2: Wide Application
PChero L298N Motor Drive Controller Board Mould is ideal for Arduino, Smart Car, Power UNO, MEGA R3, Mega 2560, etc.
Specification -
Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Maximum power: 25W
Drive voltage: 5V-35V
Drive current: 2A(For each DC motor)
Dimension: 43*43*27mm/ 1.69*1.69*1.06 inch
Operating mode: Dual H-bridge driver (can drive 2 DC motors)
Attention -
This module has a built-in 5V power supply, when the driving voltage is 7V-35V, this supply is suitable for power supply.
If driving voltage is more than 12V, please use external 5 Volt logic outputs to switch the H-bridge circuits.
DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available.
Package Included -
2 x L298N Motor Drive Controller Board Module
8. Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino
Feature
Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
Large capacity filter capacitance,afterflow protection diode, more stable and reliable.
Description
Specification:Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to +135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm
Package include:
1x L298N Module
Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply
DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2
When ENB enable IN3 IN4 control OUT3 OUT4
9. Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino
Feature
Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
Large capacity filter capacitance,afterflow protection diode, more stable and reliable.
Description
Specification:Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to +135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm
Package include:
2x L298N Module
Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply
DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2
When ENB enable IN3 IN4 control OUT3 OUT4