When you looking for betafpv f3 evo, you must consider not only the quality but also price and customer reviews. But among hundreds of product with different price range, choosing suitable betafpv f3 evo is not an easy task. In this post, we show you how to find the right betafpv f3 evo along with our top-rated reviews. Please check out our suggestions to find the best betafpv f3 evo for you.
Reviews
1. BETAFPV F3 Whoop Flight Controller with Betaflight OSD (NO Receiver Version)
Feature
The world's first compatible BetaFlight OSD, BetaFlight firmware, born for acro F3 flight controller for the Micro Whoop or Blade Inductrix quadcopter.Firmware version: Betaflight BETAFLIGHTF3. Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings.
5V, 3.3V, UART2, PPM ports are leaved for external micro receivers. Recommended micro receivers include Frsky XM / XM+, FuriousFPV LR1000, Lemon DSMX receiver, Flysky X6B etc.
Buzzer port is leaved for micro beeper. You could find your crashed drone easily with this beep function.
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
Description
BETAFPV F3 Whoop Flight Controller with Betaflight OSD (NO Receiver Version)Description:
The BETAFPV F3 FC has been designed for cutting edge FPV insanity, offering pilots the ability to push like crazy with this palm sized machine. The radio receiver interface is leaved and pilots could use any radio receiver they wanted flexibly.
With the F3 chip and MPU6000, the FC is ready for acro mode via BetaFlight, offering pilots the ability to dial in what defines the way they want to fly. Ultimate levels of FPV madness await in a feature packed layout that leaves nothing left to desire.
For fans of micro quads like the Inductrix, take your flight to an entire new world with the BETAFPV F3 FC.
Specifications:
CPU: STM32F303CCT6
Six-Axis: MPU6000
Size: 26mm x 26mm, fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight BETAFLIGHTF3
Receiver interface: 5V, 3.3V, UART2 and PPM
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.0g
Package:
1 * F3 OSD brushed flight controller (No receiver version, 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers
1 * 55mm PH-JST 1.25 power cable pigtail
2. BetaCube F3 FC Frsky Rx AIO 5.8G VTX Camera for Whoop Quads
Feature
AIO stack tower with flight controller, built in Frsky rx, camera and 5.8g vtx for micro whoop.The flight controller is BETAFPV F3+OSD+Frsky Rx flight controller
The AIO fpv camera vtx is BETAFPV Z01 camera, 25mW 5.8g vtx module with dipole antenna
The camera is connected with vtx with 1.27mm pin headers. Bend pins to set the angle of the camera
Description
DescriptionThis is the upgraded version of Betacube. A customed plastic holder is made in this newest version. Soldering is elimnated and it's all plug and play.
Frsky Rx+OSD version: F3+OSD+ Frsky Rx flight controller
The AIO 5.8gVTX camera is the new vertion BETAFPV Z01 camera
Packagge Included
1 * BETAFPV f3 brushed flight controller (all connectors soldered)
1 * BETAFPV Z01 AIO camera VTX (all connectors soldered)
1 * Plastic Z01 Holder
4 * M1.24mm screws (fit for stock Inductrix frame)
4 * M1.45mm screws (fit for Beta75 etc 75mm frame)
4 * Amti-vibration ruber dampers
3. BETAFPV F3 EVO V1.1 Whoop Flight Controller Brushed Long Range Version with Native Frsky Receiver
Feature
Newest V1.1 version is designed to fit with stock Tiny Whoop or Blade Inductrix frames completely. Add the rear mounting point for the grommet and screw on the board.SBUS with 8 channels, RSSI on channel 9 for telemetry. With PA integrated, up to 0.8 Kilometers long range
Firmware version: Betaflight SPRACINGF3EVO. Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings
Built in Frsky D8 protocol native receiver, compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
Description
The BETAFPV F3 EVO V1.1 FC has been designed for cutting edge FPV insanity, offering pilots the ability to push like crazy with this palm sized machine. Further this with FrSky compatible micro Rx,the FC is nothing short of miraculous in the world of micro FPV.
With the F3 chip and MPU6500, the FC is ready for acro mode via BetaFlight, offering pilots the ability to dial in what defines the way they want to fly. Ultimate levels of FPV madness await in a feature packed layout that leaves nothing left to desire.
For fans of micro quads like the Inductrix, take your flight to an entire new world with the BETAFPV F3 FC.
Specifications:
Model: BETAFPV V3 EVO V1.1
CPU: STM32F303CCT6
Six-Axis: MPU6500
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight SPRACINGF3EVO
Receiver: Frsky D8 potocol with PA, up to 0.8 kilometers range
Weight: 2.8g (without pigtail power cable)
Package:
1 * BETAFPV Whoop Flight Controller
4. FPV Camera BETAFPV Z01 AIO FPV Cam 5.8G 40CH 25mW Transmitter Non-OSD for Tiny Whoop Blade Inductrix etc
Feature
Z shape design to withstand worst crashes on dipole antenna5.8G FPV dipole whip high sensitivity antenna, no problem with range or durability 8 LEDs display channel and 6 LEDs display frequency group information 120 degree wide lens angle and miniature and light weight design Positioning pins designed to fit with BETAFPV F3 FC, no pigtail needed
8 LEDs display channel and 6 LEDs display frequency group information
120 degree wide lens angle and miniature and light weight design
Positioning pins designed to fit with BETAFPV F3 FC, no pigtail needed
Description
BETAFPV Z01 AIO FPV Tiny Whoop Camera 5.8G 40CH 25mW Transmitter Blade Inductrix etcThis Z01 AIO 5.8G FPV Camera is custom for Micro FPV quadcopter like Tiny Whoop etc. With the BETAFPV F3 flight controller, you could assemble the FC tower for you Tiny Whoop and no pigtail needed.
How to change the 5.8G frequency:
1. Press Band/Channel button once to change channel. Channel LEDs will skip to next one after single press.
2. Press and hold button for 4 seconds to change frequency band. Band LEDs will skip to next one accordingly.
Specification:
Output power: 25mW
Supply Voltage: 2.9-5.5v
Size : 47*14.8*12.5 mm
Weight: 3.6g
AntennaDipole whip high sensitivity antenna
Frequency: 5.8GHz 5 bands 40 channels, with Raceband: 5362~5945MHz
Field of view: 120 degrees
Antenna Port: 50
SENSOR: NTSC 640x480
LENS ANGEL: H:120/V:100
Package:
1 * BETAFPV Z01 AIO FPV Camera
5. Beta65S BNF Micro Whoop Quadcopter Integrate with OSD DSMX Receiver with 17500KV 7x16mm motors
Feature
Receiver version: DSMX Rx, Firmware version: Betaflight BETAFLIGHTF3More punch on throttle with faster 17500KV 7x16mm motors and 3-blade propellers.
BETAFPV Z01 aio 25mW vtx camera with 48 channels in total.
The DSMX version support dsm2 and dsmx protocol both. Compatible with all of the dsm2 or dsmx model aircraft models remote control, such as jr, spektrum horizon remote control.
No need to bind every time when the battery is replaced, DSMX Rx could remember your transmitter
Description
Note: Any questions, please contact us, trust us, we will solve it for you. Beta65S BNF Micro Whoop Quadcopter Integrate with OSD DSMX Rx Version with 17500KV 7x16mm motorsSpecification:
Wheelbase: 65mm
Weight: 25g (without battery)
Flight Controller: BETAFPV F3 EVO Brushed FC
Firmware version: Betaflight BETAFLIGHTF3
Motor: 7x16mm Coreless Brush Motor, 17500KV
Receiver: Frsky D8 potocol with PA / DSMX / Flysky rx with AFHDS 2A protocol
Camera and 5.8G Tx: AIO 520TVL 1/4 Inch Camera 25mW 48CH
Power connector: JST-PH 2.0 connector, AKA PowerWhoop connector
Batterry: 3.7V 230mAh Lipo battery
Flight time: 3 min 30 second
Flight controller: www.amazon.com/dp/B074GXKKZ7
Beta65S frame: www.amazon.com/dp/B074MTNKPL
7x16 motors: www.amazon.com/dp/B074MWWQHD
Package:
1 * Beta65S Micro FPV Quad
1 * BETAFPV 230mAh 1S Lipo Battery
6. BETAFPV F3 V1.1 Brushed Flight Controller Integrated with OSD and Frsky Receiver (SBUS)
Feature
V1.1 version is available now and the biggest improvement is the integrated Frsky Rx via SBUS protocol. It has a noticeable improvement when the drone turn around.The world's first compatible OSD, FrSky Rx, Betaflight, born for acro F3 flight controller for the Micro Whoop or Blade Inductrix quadcopter.Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings
Firmware version: Betaflight BETAFLIGHTF3. Built in Frsky D8 protocol native receiver (SBUS), compatible with almost ALL Frsky radios(e.g. Taranis X9D/X9D Plus/X7) or Frsky compatible transmitter module
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
The V1.1 Version could support also support DJT module. Original version not supported.
Description
BETAFPV F3 Brushed Flight Controller with OSD and Frsky Rx IntegratedSpecifications:
CPU: STM32F303CCT6
Six-Axis: MPU6000
ESC: All FETs are rated at 6.3A maximum
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version: Betaflight BETAFLIGHTF3
Receiver: Frsky D8 potocol (SBUS)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 2.96g
Package:
1 * F3 OSD brushed flight controller ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers
1 * 55mm PH-JST 1.25 power cable pigtail
7. BETAFPV Beta75 BNF Tiny Whoop Quadcopter Native Frsky receiver Integrate with OSD
Feature
Please note: send without a usb charger.Firmware version: Betaflight BETAFLIGHTF3 . Beta75 bulit with Insane integrate with OSD : https://www.youtube.com/watch?v=IfdogjN80UE&feature=youtu.be
The same hole pattern with Tiny Whoop flight controller.More punch on throttle with 7x20mm motors and 3-blade 40mm propellers.
Built in Frsky rx is compatible with Taranis, Taranis Plus, X9E etc. This built in receiver integrate a power amplifier IC (PA) RFX2401C, so you could get up to long range. This is the biggest improvement than other board with no PA included.
The struts between the motor mounts and ducts are fragile and break easily. So these upgraded frames stiffen the struts considerably. The struts have a flat cross section which creates more bonding area with the duct.
Description
BETAFPV Beta75 BNF Tiny Whoop Quadcopter Native Frsky receiver Integrate with OSDDescription:The Beta75 is only about 1cm larger than the Tiny Whoop Quad. The biggest difference is the propulsion system. With 7x20mm motors and tri-blade 40mm props, it feels very fast, perfect for indoor racing and acro flying. The performance in outdoor is also great, handles the light breezes very well where the Tiny Whoop tend to struggle to stay level.
It has a motor to motor distance of 75mm ( 65mm for Tiny Whoop ). The width and length of the quad measure at 105mm. Compared to other micro quads with brushless motors, the price of Beta75 is really attractive, perfect for beginners and FPV racers alike.
Specification:
Wheelbase: 75mm
Weight: 32g (without battery)
Flight Controller: BETAFPV F3 EVO Brushed FC with Native Frsky receiver
Firmware version: Betaflight BETAFLIGHTF3
Motor: 7x20mm Coreless Brush Motor, 17500KV
Receiver: Frsky D8 potocol with PA
Camera and 5.8G VTX: AIO 520TVL 1/4 Inch Camera 25mW 40CH
Battery: 4.35V 230mAh Lipo battery with PowerWhoop connector
Flight time: 3 min 30 second
Package:
1 * BNF Beta75 Micro FPV Quad ( Frsky Rx No Battery)
8. BETAFPV F3 Brushed Flight Controller DSMX Receiver Integrated with OSD
Feature
The world's first compatible BetaFlight OSD, DSMX Rx, BetaFlight firmware, born for acro F3 flight controller for the Micro Whoop or Blade Inductrix quadcopter.Fully programmable through Betaflight, using the onboard USB port, tune all the parameters, PID's, and rates to your perfect settings
Firmware version: Betaflight BETAFLIGHTF3. Built in DSMX protocol native receiver (SBUS), compatible with almost ALL Spektrum radios(e.g. Spektrum DX6/DX6i/DX8...) or DSMX compatible transmitter module
The flight controller board comes pre-flashed with Betaflight firmware, and pre-soldered 55mm power cable pigtail with JST-PH 2.0 connector, AKA PowerWhoop connector.
This Flight controller is a 1 time binding procedure for Spektrum. You don't have to bind every time when changing the battery
Description
BETAFPV F3 Brushed Flight Controller Integrated with OSD and DSMX ReceiverSpecifications:
CPU: STM32F303CCT6
Six-Axis: MPU6000
ESC: All FETs are rated at 6.3A maximum
Size: 26mm x 26mm,fully compatible with the Inductrix quad frame and mounting pattern
Firmware version:Betaflight BETAFLIGHTF3
OSD: Built-in BetaFlight OSD (STM32 controls OSD chip over SPI in DMA mode)
Receiver: DSMX potocol (SBUS)
Power Cable: 55mm, with JST-PH 2.0 connector, AKA PowerWhoop connector
Weight: 3.2g
Package:
1 * F3 OSD brushed flight controller with DSMX receiver ( 55mm PH-JST 2.0 power cable soldered)
4 * M1.2x4mm screws (Fit for stock Inductrix frame)
4 * M1.4x5mm screws (Fit for Beta75 etc 75mm frame)
4 * Anti-vibration ruber dampers
1 * 55mm PH-JST 1.25 power cable pigtail
9. BETAFPV Beta75S BNF Tiny Whoop Quadcopter Frsky Receiver with OSD for 8X20 Motor
Feature
Great alternative to popular Tiny Whoop quadcopter.More punch on throttle with 8x20mm motors and 3-blade 40mm propellers.
The same hole pattern with Tiny Whoop flight controller.
The Beta75S has 2 improvement based on Beta75 drones: 1.Motors: 7x20mm -> 8x20mm brushed motors. 2.Battery: 260mAh -> 550mAh Lipo HV battery
Description
SpecificationWheelbase: 75mm
Weight: 32g (without battery)
Flight Controller: BETAFPV Brushed FC with OSD
Firmware Version: Betaflight BETAFLIGHTF3 3.2.0
Motor: 8x20mm coreless brushed motor, 14000KV
Receiver: Frsky D8 potocol
Camera and 5.8G Tx: AIO 520TVL 1/4 Inch Camera 25mW 40CH
Batterry: 550mAh Lipo HV battery with PowerWhoop connector
Flight time: 5 min
ASSEMBLY PARTS LIST
Frame: Beta75S frame
Motors: 8x20mm brushed motors
Props: 40mm 3-blades props
FC: BETAFPV F3 FC with OSD (According to different Rx version)
AIO camera: Z01 Camera
Battery: 550mAh LiHV battery
FRSKY RX VERSION
The Frsky version support D8 protocol only. Compatible with Frsky Taranis X9D/ X9D Plus etc. So it is incompatible with Frsky Taranis radio transmitter in EU firmware.
Find out which firmware you have on your radio.
So if you have a Frsky radio transmitter in EU firmware and want to try the OSD function, we would recommend the no receiver version. You could add an external micro receiver that support the D16 protocol, like Frsky XM etc.
Package Including
1 * BNF Beta75S Micro FPV Quad
1 * BETAFPV 550mAh 1S Lipo HV Battery