When you want to find mosfet anet a8, you may need to consider between many choices. Finding the best mosfet anet a8 is not an easy task. In this post, we create a very short list about top 9 the best mosfet anet a8 for you. You can check detail product features, product specifications and also our voting for each product. Let’s start with following top 9 mosfet anet a8:
Reviews
1. BIQU Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer
Feature
A general add-on heated bed power expansion module for 3D printerCompletely solve the hot bed power is too large and the load current issue. It can work with the Anet A8
With this addon module to your 3D printer motherboard you can lead the maximum current up to 15A
Under the premise of normal heat dissipation, this module can work steadily under the condition of I(Max)=15A. Don't exceed 15A during the process.)
If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this module is recommended, else it may cause excessive current during times which may burn the connectors on the controller board, According to the thermal power of the bed, please choose the appropriate power supply, with sufficient margin. If it is large power heated, we suggest 24V power supply, under the same power requirements, current is less than 12 v
Description
Product Description:
Features: Dimensions:60x50mm
Mounting holes:3.2mm diameter, for M3 screws
DCIN: "+" connect the power positive electrode: "-"connect the power negative, electrode(support "+ 12 v"or "+ 24 v" power supply, it is recommended to use + 24 v power supply)
Heatbed: connect to heatbed line(there are no positive or negative)
Connect the heatbed control port on the motherboard(there are no positive or negative)
Note:
1.When you connect power supply cable, you need to pay attention to distinguish the positive and negative polarity of the power supply,and do not reverse the connection of the cable to avoid burning the module and causing unnecessary losses
2.Module placement problem: when you use the module, do not put it in a place where the wires are dense. In this way, it helps to reduce the heating burden on the module and increase the safety
3.When the module is working: don't let the conductor to touch its bottom, it can prevent short circuit and burn out
Packge Included:
1 x Heated Bed Mosfet
1 x Connection cable for input signal
2x Cable for heat bed connect Wire
2x Cable for power
2. 3D Printer Heat Bed Power Module SIMPZIA General Add-on Hot Bed Mosfet MOS Tube High Current Load Module for 3D Printer Hot Bed/Hot End(2 Pack)
Feature
MOSFET APPLICATION:This high power module is a general add-on heated bed power expansion module for 3D printer.After Sales Quality Guarantee:All of our mosfets past quality inspection before shipment, Anyone receives a defective one please contact us, we guarantee to ship the new replacement.
A GOOD REPLACEMENT:This is a great creative part, is what you need, if your heated bed has stopped working due to MOSFET failure.
GOOD PROTECTION: When using heated bed 3D printer for 12V power supply which may cause excessive current during times, with this module, it can well protect the connectors on the controller board from burning.
Description
It stays cool and saves your control board from melting.The included wire and terminal connectors are a nice touch. This module generally rests on top of the control box or next to the control board.
Features:
Color: Black
Size: 6 x 5 x 3.1cm / 2.36 x 1.97 x 1.22"
Mounting holes: 3.2mm diameter, for M3 screws.
Max Current: 25A (Enhance heat dissipation) safe for prolonged times. ensure active cooling of the heatsink.
This module is based on power MOSFET and will allow PID control of the heated bed (DC-DC Relays usually do not allow this)
Note:
This module under the premise of normal cooling, found at I (Max) = 25A stable work situation, the process of using the current not exceed 25A.
Packing Included:
2 x Heated Bed Power Expansion Module
2 x Connection cable for input signal
2x Cable for hot bed
2x Cable for power
3. Mosfet 3D Printer, FYSETC Heat Bed Power Module Add-on Hot Bed Mosfet Tube High Current Load Module for 3D Printer Anet A8 Prusa i3 and More - 2 Pack
Feature
Heat bed Mosfet: apply to solve the problem of hot bed's large power and the load current, can work well with the Anet A8.General motherboard's Maximum current is 15A, this add-on Mos module to board lead the maximun current up to 25A.
Please Kindly Note: under the premise of normal cooling, it work stable under I(Max)=25A, so we suggest the current must not exceed 25A while the process working.
The hot bed module can be used in both Chitu motherboard and other open 3D printer motherboards.
Wire is 14AWG and 30-60 cm length, each module has done functional test before shipment, anyone receives a defective one please contact us, we will give you support within 24 hours.
Description
What is Mosfet Module?1. If you intend to use heated bed with your 3D printer that uses a 12V(15A current) power supply, then this module is recommended, else it may cause excessive current during times which may burn the connectors on the controller board.
2. Another saying, If you need anything greater or equal to 15A this module is a must! For example, if your total power usage is 240W and you have 12V power supply, then it means at least 20A current is needed (20X12=240W). As ChiTu controller board is only capable of 15A this setting will not work. To make it work, you need this extra power module.
3. With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A.
Feature:
Dimensions(LxWxH): 6 x 5 x 3 cm/ 2.4" x 2" x 1.2"
Supply/Operating Voltage: 12V-50V (12-24VDC recommended)
This module is based on power MOSFET and will allow PID control of the heated bed (DC-DC Relays usually do not allow this)
Package included:
2 x Heated Bed Power Module
2 x Connection cable for input signal
4 x Power Connection Cables
4 x Hot Bed Connect Wires
4. ARQQ Heat Bed Mosfet Tube Hot Bed Power Module Expansion for 3D Printer Heating Bed Accessories(Pack of 2)
Feature
Work with anet a8 3d printer heat bedCompletely solve the hot bed power is too large and the load current issue
Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
General Add-on Heated Bed Power Expansion Module
Note: Any issue please contact us before, we will always here to help!
Description
Details: Dimensions: 60*50mm
Net Weight: 40g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Wire's color is random
Summary:
1. Remove basically all ouside screws for your anet a8 control box
2. Take pictures of existing board wiring
3. Unscrew two large 12/14GA wires on the board labeled "hot bed"
4. Screw these two wires into the new mosfet board labled "hot bed"
5. Connect the small jumper wires (white) to the control board where you just removed the two wires and screw them down. Note the polarity on each board. Match (+) to (+) and (-) to (-)
6. FInd 2x 6-8" pieces of 12 or 14 AWG wire. Most cheap extension cords are 16AWG (too thin). Your local home depot / menards / ace will have this as cut-to-length
7. Run one of the 6" wires to the power supply (+), screw in; and the other side to the (+) DC IN on the new mosfet board. Repeat for the negative wire (-) to (-)
8. Many people use velcro to secure the new board to the top of the control box. Others print off a holder from thingiverse
9. Put everything back together
10. When complete, you'll see a blue light activate for signal from inside the box when the bed heater is activated by the control board
Package Included:
2xHot bed MOS Tube Power Module Expansion
5. BIQU Heat Bed Power Module Expansion Hot Bed MOS Tube for 3D Printer(Pack of 2pcs)
Feature
Currently work with the Anet A8Completely solve the hot bed power is too large and the load current issue
General add-on heated bed power expansion module
With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A
Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working
Description
Specifications:
Dimensions: 60*50mm
Net Weight: 25g
Color:Black
Max Current: 25A(Enhance heat dissipation)
Helps 3D printer equipped with the controller board (capable of max 15A) become more powerful
With this add-on module to board lead the maximum current up to 25A
If you intend to use heated bed with your 3D printer that uses a 12V power supply, then this module is recommended, else it may cause excessive current during times which may burn the connectors on the controller board, According to the thermal power of the bed, please choose the appropriate power supply, with sufficient margin. If it is large power heated, we suggest 24V power supply, under the same power requirements, current is less than 12 v
Package Included:
2*Heat bed Power Module
Note:
Please double-confirm the wire you connect is right, if there have any issue please contact us before leave negative review and feedback, thanks!
6. SIMPZIA 3D Printer Heat Bed Power Module General Add-on Hot Bed Power Expansion Board MOS Tube High Current Load Module - 4 Pack
Feature
APPLICATION: This high power module is a general add-on heated bed power expansion module for 3D printer. It can work with the Anet A8.MOTHERBOARD: The heat bed power module can be used in both Chitu motherboard and other open 3D printer motherboards.
25A MAXIMUM CURRENT: This high power module helps your 3D printer equipped with the Chitu controller board (capable of max 15A) become even more powerful. With this add-on module to board lead the maximum current up to 25A.
GOOD PROTECTION: When using heated bed 3D printer for 12V power supply which may cause excessive current during times, with this module, it can well protect the connectors on the controller board from burning.
PACKAGE INCLUDES: 4 x Heated bed power module (motherboard is not included) and 4 x Connection cable for input signal.
Description
Features:Color: Black
Size: 6 x 5 x 3.1cm / 2.36 x 1.97 x 1.22"
Mounting holes: 3.2mm diameter, for M3 screws.
Max Current: 25A (Enhance heat dissipation) safe for prolonged times. ensure active cooling of the heatsink.
This module is based on power MOSFET and will allow PID control of the heated bed (DC-DC Relays usually do not allow this)
Note:
This module under the premise of normal cooling, found at I (Max) = 25A stable work situation, the process of using the current not exceed 25A.
Packing Included:
4 x Heated Bed Power Expansion Module
4 x Connection cable for input signal
8 x Connection Wires for Hot Bed
8 x Power Cords
7. Heat Bed Mosfet, MACTISICAL 2 Pack 3D Printer Heat Bed Power Module 3D Printer Board Expansion Board MOS Tube High Current Load Module
Feature
WELL MADE- New material with superior quality stainless, High-grade Aluminum block for best connectivity and long life.HIGH TRANSMISSION - With this addon module to your 3D printer motherboard you can lead the maximum current up to 25A.
MULTIFUNCTION - Completely solve the hot bed power is too large and load current problems,and can well protect the connectors on the controller board from overheating.
MEET YOUR NEEDS -Widely used for common 3D printer models,extruder and other open 3D printer motherboards.such as Anet A8, etc.
WARNING - For use on some devices (for example,Anet A8),you need to make sure the power supply is set to 110 volts instead of the default 220 volts.If the voltage is too high, the product will get super hot, even charred!! Don't touch it lightly.
Description
100% Brand new and Premium Professional Grade MACTISICAL 3D Printer Hot Bed Power Expansion Board .
This module is based on power mosfet and will allow PID control of the heated bed (DC-DC Relays usually do not allow this).
According to the thermal power of the bed, please choose the matching power supply, with sufficient margin.High-Power heated bed is recommended to use 24V power supply,under the same power requirements, the current is smaller than 12V.
Specification
Color: Black, cable length: 6 inch
Net Weight: 75g(approx.)
Size: 2.36" x 1.97" x 1.2" / 60mm x 50mm x 30mm
Mounting Holes: D=3.2MM For M3 Screws.
Notice:
Under the premise of normal cooling, it work stable under I(Max)=25A, the current must not exceed 25A while the process working.
Package Content:
2*Heat bed Power Module with 2 connection cables
Support
Please do not hesitate to contact us if there's any problem or question about our products. We will keep improving our products and service, and try our bestto meet customers' needs. Thank you for supporting MACTISICAL.
8. WINGONEER 5Pcs IRF520 MOSFET Driver Module
Feature
Example Code and Datasheet available on our support forumWeight: 10g
Size: 33 x 24mm
Max load (drain) current: <5A
Output load voltage :0-24V
Description
WINGONEER trademark Reg.NO:4747611This little module (HCMODU0083) is a breakout board for the IFR520 MOSFET transistor. The module is designed to switch heavy DC loads from a single digital pin of your microcontroller. Its main purpose is to provide a low cost way to drive a DC motor for robotics applications, but the module can be used to control most high current DC loads. Screw terminals are provided to interface to your load and external power source. An LED indicator provides a visual indication of when your load is being switched.
Specification
Weight: 10g
Size: 33.5 x 25.5mm
Max load (drain) current: <5A
Output load voltage :0-24V
Input Voltage: 3.3V, 5V
Package Included:
5x WINGONEER IRF520 MOSFET Driver Module
9. ANYCUBIC 3D Printer Heating Controller MKS MOSFET for Heatbed Extruder MOS Module
Feature
Each one has done functional testSuperior performance of MOSFET (Max 280A)
Extra large heat sink , the maximum current can be up to 30A or more
Can use hot bed output signal of Ramp1.4 and MKS series to control
Can use digital signal of 5-24v to control
Description
Usage :1. Connect Power to power source, please note the anode and cathode.
2. Connect Hotbed to heated wire , please note the anode and cathode.
3. Connect digital control signal to Gnd,D8.
4. Connect the control signal of Ramps1.4 or MKS MOSFET to Bed
5. Choose one signal group to connect.
package included:/b>
1 x MOS module