Finding the best flight controller gps osd suitable for your needs isnt easy. With hundreds of choices can distract you. Knowing whats bad and whats good can be something of a minefield. In this article, weve done the hard work for you.
Reviews
1. Hobbypower Pixhawk PX4 Flight Controller W/ Shock Absorber +NEO-M8N GPS 915Mhz Radio Wireless Telemetry Set OSD Module PPM Module I2C Splitter Expand Module Power Module for FPV Quadcopter Multirotor
Feature
Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating systemBus interface (UART, I2C, SPI, CAN)
Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control
Provide redundant power input and fault transfer function
Provide automatic and manual mode
Description
Pixhawk V2.4.8 32Bit Flight Controller- Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
- 14* PWM/ actuator output;
- Bus interface (UART, I2C, SPI, CAN);
- Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control;
- Provide automatic and manual mode;
- Provide redundant power input and fault transfer function;
- Color LED lamp;
- Multi tone buzzer interface;
- Micro SD to record flight data;
Processor:
- 32 bit 2M flash memory STM32F427 Cortex M4, with hardware floating point processing unit
- Main frequency: 256K, 168MHZ RAM
- 32 bit STM32F103 backup co processor
Sensor:
- L3GD20 3 axis digital 16 bit gyroscope
- LSM303D 3 axis 14 bit accelerometer /magnetometer
- MPU6000 6 axis accelerometer / magnetometer
- MS5611 high precision barometer
Interface:
- 5* UART, 1*compatible high voltage, 2*hardware flow control
- 2*CAN
- Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
- Futaba SBUS compatible input and output
- PPM signal input
- RSSI (PWM or voltage) input
- I2C
- SPI
- 3.3 and 6.6VADC input
- External USB MICRO interface
Package includes:
1x Pixhawk V2.4.8 Flight Controller(comes with Buzzer,Switch,8G SD Card)
1x NEO-M8N GPS module
1x Power module
1x OSD Module
1x 3DR 915Mhz Radio Wireless Telemetry set
1x PPM Module
1x I2C Splitter Expand Module
1x GPS bracket
1x Shock Absorber
2. Wolfwhoop Whoop-Tower Pro OMNIBUSF4 Pro Flight Controller FC Integrated OSD PDB VTX 4 in 1 Super Tower RC FPV Racing Drone Quadcopter
Feature
The wiring has been optimized, which requires less soldering steps, thus making the assembling simple and quick when used in combination with PW-010.Support 3S-4S power input, Easy and quick OSD configuring
The VTX can be configured by RC transmitter via SA, or you can change setting directly by button.
Integratedwith STM32 F405 chip, compatible with Betaflight and Cleanflight (supports DHOTS150/300/600/1200) ESC with high operating speed, which achieves excellent flight experience. Moreover, it can generate powerfulcalculatingability and velocity, gives pilots easier, more stable and smooth flight experience
Please find more information from the detailed manual:http://wolfwhoop.com/uploadfile/2018/0108/20180108040146466.pdf Feel free to contact customer service by: [email protected]
Description
4032FC flight controls features:
* the wiring has been optimized, which requires less soldering steps, thus making the assembling simple and quick when used in combination with PW-010.
* Support 3S-4S power input
* Integratedwith STM32 F405 chip, compatible with Betaflight and Cleanflight (supports DHOTS150/300/600/1200) ESC with high operating speed, which achieves excellent flight experience. Moreover, it can generate powerfulcalculatingability and velocity, gives pilots easier, more stable and smooth flight experience.
*MPU 6000 6-axis gyroscope
* 280 barometer
*Supports receivers like SBUS PPM IBUS DSM2, etc.
* Easy and quick OSD configuring.
*Reserved soldering place for Buzzer and programmable LED light.
*Support SD slot
*Size:36*36MM(FC-4032) 48*36MM(PW-0010)
*Standard flight controller installation hole size: 30.5X30.5mm
*Firmware: Omnibus F4SD 3.2.2(factorydefault)
* Integrated BEC 5V output: 5V/1.5A (max:2A)
*LED strip has already connected with A08 through short circuit in factory default setting, for future firmware upgrading, please distribute LED connector to A08 and Save. Otherwise LED strip will not work.
For example: resource LED_STRIP 1 A08 (distribute LED connector to A08 and Save)
3. Hobbypower APM2.8 Flight Controller + NEO-M8N GPS, 3DR 915Mhz Telemetry, OSD, Power Module
Feature
APM2.8 Flight ControllerNEO-M8N GPS module
3DR 915Mhz Radio Wireless Telemetry Kit
Crius MAVLink-OSD V2.1
Crius Power Module
Description
Package includes:1x APM2.8 FC with Shock Absorber
1x NEO-M8N GPS module
1x Crius APM power module
1x Crius MAVLink-OSD V2.1
1x 3DR 915Mhz Radio Wireless Telemetry Kit
1x GPS bracket
1x 3DR Telemetry OSD Y Style Connection Cable
4. FlightOne Revolt OSD Flight Controller
Description
Features
- Fast building using connector system
- Full Lipo up to 6s rating
- Advanced filtering
- Plug and Play
- Built in internal OSD
- LED Driver for WS2812b programmable LED
- SBUS Inversion
- High Speed 32khz gyro, lowest noise floor and highest sensitivity gyro everused
- Through hole solder pads forms an I-Beam when soldered for extra strength
- FrSky Taranis, Spektrum, Futaba, JR, IBus, Sbus and other radio support
- Integrated buzzer driver
- Voltage and current ADC pins, for full voltage and current monitoring
- Full telemetry output support
- ESC flashing and configuration built into configurator
- Most active software development
- Selectable 3.3 voltage
- 3 serial uarts
- Bluetooth expandable
- F4 processor
- 16mb of flash memory
- GPS expandable
- Pins into FlightOne Bolt 4in1 ESC
- Dimensions: 36mm x 36mm
- Mounting holes: 30.5mm squared to center of holes
- Weight: 6 grams
- Easily connectable to the FlightOne Bolt with our special connector.
Revolters will also get access to FlightOnes ticketed tech support which will include step-by-step help with installation, tuning, and anything else that may arise with your Revolt.
5. Hobbypower APM2.8 Flight Controller and NEO-M8N GPS, 3DR 433Mhz Telemetry, OSD, Power Module
Feature
APM2.8 Flight ControllerNEO-M8N GPS module
3DR 433Mhz Radio Wireless Telemetry Kit
Crius MAVLink-OSD V2.1
Crius Power Module
Description
APM2.8 Flight Controller- Newest APM version, with Shock Absorber designed
- Arduino Compatible
- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
- Onboard 4 MegaByte Dataflash chip for automatic datalogging
- One of the first open source autopilot systems to use Invensense's 6 DOF Accelerometer/Gyro MPU-6000.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and USB functions respectively.
NEO-M8N GPS & Compass Module
Receiver type 72-channel u-blox M8 engine - Nav. update rate1 Single GNSS: up to 18 HZ
3DR 433Mhz Radio Wireless Telemetry Kit (detail instruction please reference this link)
- 433-434.79MHz
- Receiver sensitivity to -121 dBm
- Transmit power up to 20dBm (100mW)
- Transparent serial link
- Air data rates up to 250kbps
- MAVLink protocol framing and status reporting
- Frequency hopping spread spectrum (FHSS)
- Adaptive time division multiplexing (TDM)
- Support for LBT and AFA
- Configurable duty cycle
- Built in error correcting code (can correct up to 25% data bit errors)
Package includes:
1x APM2.8 FC with Shock Absorber
1x NEO-M8N GPS module
1x Crius APM power module
1x Crius MAVLink-OSD V2.1
1x 3DR 433Mhz Radio Wireless Telemetry Kit
1x GPS bracket
1x 3DR Telemetry OSD Y Style Connection Cable
6. Hobbypower APM2.8 Flight Controller NEO-7M GPS 3DR 915Mhz Telemetry Mini OSD Module Power Module for FPV Quadcopter Multirotor
Feature
Newest APM version, with Shock Absorber designedPackage includes: 1x APM2.8 Flight Controller with Shock Absorber , 1x NEO-7M GPS module, 1x power module, 1x Mini OSD Module, 1x 3DR 915Mhz Radio Wireless Telemetry set, 1x GPS bracket
Description
APM2.8 Flight Controller- Newest APM version, with Shock Absorber designed
- Arduino Compatible
- Includes 3-axis gyro, accelerometer and magnetometer, along with a high-performance barometer
- Onboard 4 MegaByte Dataflash chip for automatic datalogging
- One of the first open source autopilot systems to use Invensense's 6 DOF Accelerometer/Gyro MPU-6000.
- Barometric pressure sensor upgraded to MS5611-01BA03, from Measurement Specialties.
- Atmel's ATMEGA2560 and ATMEGA32U-2 chips for processing and USB functions respectively.
- Drawing:http://img01.taobaocdn.com/imgextra/i1/664694061/TB2JsClXVXXXXa4XXXXXXXXXXXX- 664694061.jpg
NEO-7M GPS & Compass Module
U-blox NEO-7M GPS module
Build in 25 x 25 x 4mm ceramic patch antenna
LNA and SAW chip
3.3V LDO low noise regulator
UART (TTL) port with EMI protection
3V Rechargeable Backup Capacitors
Fix indicator LEDs
Reverse polarity protection for input power
NMEA protocol
Baud rate : 9600
Nav rate : 1Hz
TIMEPULSE (fix LED) rate : 1Hz
Package includes:
1x APM2.8 Flight Controller with Shock Absorber
1x NEO-7M GPS module
1x power module
1x Mini OSD
1x 3DR 915Mhz Radio Wireless Telemetry Kit
1x GPS bracket
7. Pixhawk PX4 PIX 2.4.8 32 Bit Flight Controller+433/915 Telemetry+M8N GPS+Minim OSD+PM+Safety Switch+Buzzer+RGB+PPM+I2C (915 250mw Telemetry)
Feature
1. The advanced 32-bit ARM CortexM4 high-performance processors, can run NuttX RTOS real-time operating system;2. 14 PWM / servo output; 3. Bus interface (UART, I2C, SPI, CAN);
4. The integrated backup power and backup controller fails, the primary controller fails over to the backup control is safe;
5. Provide automatic and manual modes; 6. Provide redundant power input and failover; 7. Multicolor LED lights;
8. Provide multi-tone buzzer Interface 9. Micro SD recording flight data;
Description
Specifications:
Microprocessor:
1.32 2 MB flash STM32F427 Cortex M4, with hardware floating-point processing unit
2. frequency: 168MHZ, 256K RAM
3.32 STM32F103 backup coprocessor
Sensor:
1.L3GD20 3-axis digital gyroscope 16
2.LSM303D 3-axis accelerometer 14 / Magnetometer
3.MPU6000 6-axis accelerometer / magnetometer
4.MS5611 precision barometer
Interface:
1 .5 high voltage compatible UART 1, 2 with hardware flow control
2. 2 CAN
3.Spektrum DSM / DSM2 / DSM-X satellite receiver compatible input
4.Futaba SBUS compatible inputs and outputs
5.PPM Signal Input
6.RSSI (PWM or voltage) Input
7.I2C
8.SPI
9.3.3 and 6.6VADC input
10. External MICRO USB Interface
Packing list:
Pixhawk 2.4.8 32bit ARM Flight Controllerx 1
Safety buttonx 1
Buzzer x 1
8G TF card (IO firmware has written) x1
Neo-M8N Gps Module x1
Black Gps Holder x1
Power Module x1 ( yellow and black color XT60 connector PM send at random
Minim OSD w/ shell x1 ( 2 kind of OSD cable send at random)
I2C Splitter Expand Module x1
PPM Module w/ shell x1
RGB module 1
433/915 MHZ telemetry x1 ( send by your choice)
6pin turn 6pin cable x 1
4pin turn 4pin cable x 1
3pin DuPont line x1,
Product item KKK999
8. Hobbypower Pixhawk PX4 Flight Controller W/ Shock Absorber + NEO-M8N GPS 433Mhz Radio Wireless Telemetry OSD Moodule PPM Module I2C Splitter Expand Module Power Module FPV Multirotor Quadcopter
Feature
Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating systemBus interface (UART, I2C, SPI, CAN)
Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control
Provide redundant power input and fault transfer function
Provide automatic and manual mode
Description
Pixhawk V2.4.8 32Bit Flight Controller- Advanced 32 bit CortexM4 ARM high performance processor, can run RTOS NuttX real time operating system;
- 14* PWM/ actuator output;
- Bus interface (UART, I2C, SPI, CAN);
- Integrated backup power supply and failure backup controller, the main controller can be safely switched to backup control;
- Provide automatic and manual mode;
- Provide redundant power input and fault transfer function;
- Color LED lamp;
- Multi tone buzzer interface;
- Micro SD to record flight data;
Processor:
- 32 bit 2M flash memory STM32F427 Cortex M4, with hardware floating point processing unit
- Main frequency: 256K, 168MHZ RAM
- 32 bit STM32F103 backup co processor
Sensor:
- L3GD20 3 axis digital 16 bit gyroscope
- LSM303D 3 axis 14 bit accelerometer /magnetometer
- MPU6000 6 axis accelerometer / magnetometer
- MS5611 high precision barometer
Interface:
- 5* UART, 1*compatible high voltage, 2*hardware flow control
- 2*CAN
- Spektrum DSM/DSM2/DSM-X satellite receiver compatible input
- Futaba SBUS compatible input and output
- PPM signal input
- RSSI (PWM or voltage) input
- I2C
- SPI
- 3.3 and 6.6VADC input
- External USB MICRO interface
Package includes:
1x Pixhawk V2.4.8 Flight Controller(comes with Buzzer,Switch, 1G SD Card)
1x NEO-M8N GPS module
1x Power module
1x OSD Module
1x 3DR 433Mhz Radio Wireless Telemetry set
1x PPM Module
1x I2C Splitter Expand Module
1x GPS bracket
1x Shock Absorber
9. QWinOut DIY FPV Mini Drone Autopilot Combo Set Mini CC3D Revolution Flight Controller + OP GPS + OSD + OPlink 433mhz Mini Air & Ground Telemetry Module Kit
Feature
Mini CC3D Revolution Flight ControllerOplink 433mhz Mini Air & Ground Telemetry Module
Mini OSD
OP Mini GPS
Dimensions: 38mm x23mm x10mm (included case)
Description
Package Included:1 x Mini CC3D Revolution Filght Controller
1 x OP Mini GPS
1 x Mini OSD
1 x OPlink mini Air Module 433MHz with Antenna
1 x OPlink mini Grond Module 433MHz with Antenna
1 x Distribution Board
More Detail:
Mini CC3D Revolution Flight Controller
STM32 F4 Microcontroller
Invensense MPU-6000 Gyro/Accel
MS5611 baro
Main port
Flexi Port (serial or I2C port)
Rc input port
Pwm output port
Comes with Case
Case:30mm x23mm x9mm.
Weight: 6g (includes case)
Oplink mini Air
Dimensions:34mm x19.5mm x10.5mm (included case)
Frequency:433mhz
Input Voltage: +5v
Oplink mini ground
100mw Standalone Radio Modem
3 IO Ports: Micro-B USB, Mainport & Flexiport
Dimensions: 38mm x23mm x10mm (included case)
Input Voltage: +5v
Frequency:433mhz
10. Aoile Matek System 20x20mm F411-mini Mini F4 Flight Controller AIO OSD BEC LED Strip RC Drone
Feature
- 20x20mm Mounting hole, only 4.5g.- with betaflight OSD and 5V BEC output.
- with 2 LED indicator, blue and red.
- Built in inverter for SBUS input (UART1-RX).
- PPM/UART Shared: UART2-RX.
Description
Description:
Item Name: 20x20mm Mini F4 Flight Controller AIO OSD BEC and LED Strip
MCU: 100MHz STM32F411
IMU: MPU6000
OSD: BetaFlight OSD w/ AT7456E chip
Camera control supported on Rssi pad
Battery Voltage Sensor: 1:10
Current Sensor: No (FCHUB-A option)
BEC: 5V 2A
LDO 3.3V: Max.300mA
I2C1 SDA & SCL available
WS2812 Led Strip : Yes
Built in inverter for SBUS input (UART1-RX)
PPM/UART Shared: UART2-RX
SoftSerial supported on S5 & S6
Beeper : Yes
RSSI: No
Blackbox: No
Size: 28x28mm
Mounting Hole: 20x20mm
Weight: 4.5g
Package include:
1x F4 Flight Controller
6x Silicon grommets M4 to M3
6x Brass grommets M3 to M2
Feature:
--High strength
--Long life service
The colors deviation might differ due to different monitor settings, please kindly understand.
Please tell us first when you have any problem, we will give you the best service and solve the problem ASAP. Thank you so much.