When you want to find dc motor driver, you may need to consider between many choices. Finding the best dc motor driver is not an easy task. In this post, we create a very short list about top 9 the best dc motor driver for you. You can check detail product features, product specifications and also our voting for each product. Let’s start with following top 9 dc motor driver:
Reviews
1. DROK DC 5-36V 400W Dual Large Power MOS Transistor Driving Module, FET Trigger Switch Board, 0-20KHz PWM Electronic Switch Control, DC Motor Speed Controller
Feature
High-quality components: drok adopts imported large power dual-mos Transistor parallel active output, lower resistance, higher current and strong powerPowerful output capability: at room temperature, the module can continuously provide 15A, 400W, which can satisfy most of devices if enhance heat dissipation, the max current output can up to 30A
Various trigger signal source: this mos Transistor board can be triggered by digital High-Low (DC3 3v-20v)and can be connected Windows port of microcontroller, PLC interfaces, DC power, etc
Perfect support PWM signal: the PWM controller can access PWM signal, which can perfectly supported the frequency of 0-20khz
Wide application: this motor control module can tolerate wide input Voltage (DC 5-36v) it can be applied in various high power equipments, such as motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid Valve; can input PWM to control motor speed or Lamp Brightness
Description
Technical Parameters:Operating voltage: DC 5V - 36V;
Trigger source: digital high-low (DC3.3V-20V) (can be connected IO port of microcontroller,
PLC interfaces, DC power, etc.. The module can access PWM signal, which can perfectly supported the frequency of 0-20KHZ.)
Output voltage: DC 5V - 36V,
Output current: 15A (continuous current, at room temperature. Enhance heat dissipation, the max. current can up to 30A)
Output power: 400W
Operating temperature: -40-85
Dimension: 34 17 12mm.
Application:
High Power equipment, motors, light bulbs, LED lights, DC motors, micro-pumps, solenoid valve; can input PWM to control motor speed or lamp brightness.
Package Includes:
1 MOS Driving Module
2. ELEGIANT DC 10-50V 60A High Power Motor Speed Controller PWM HHO RC Driver Controller Module 12V 24V 48V 3000W Extension Cord with Switch
Feature
Compact in size, wide voltage & current range.Use PWM modulation system to adjust light & speed.
With radiators to doing heat dissipation created by MOS tube.
With wire to connect potentiometer for more convenient speed control.
Protective case creates better durability; max power of 3000W and small noise.
Description
Specifications:Working Voltage: DC 10-50 V
Rated Current: 60A
PWM Frequency: 15KHz
Control Power: 0.01-3000 W
12V: 720W(max)
24V: 1440W(max)
36V: 2160W(max)
50V: 3000W(max)
Quiescent Current: 0.04 A
PWM Duty Ratio: 5-100%
Working Temperature: -20 to +40
Weight: 6.53oz
Item Size: 4.72 x 3.35x 1.02in
Main Application:
1.Universal DC motor speed control.
2.Automotive motor speed control (eg. cars, car wiper, car fan motor, car cooling fan motor, air condition fan motor)
3.Adjust speed of the conveyor of product lines, tube exhaust fan, treadmill, electric fan.
4.Adjust temperature of DC heater, brightness of common DC bulb.
Package List:
1 x PWM DC Motor Speed Controller
3. kuman L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control & Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove Nano Robot K48
Feature
The module using ST L298N chipset,has strong driver capability,afterflow protection diode, more stable and reliable.Logical voltage 5V. Drive voltage 5V-35V Drive current 2A(MAX single bridge). Max power 25W Storage temperature: -25 ~ +130
Size:43*43*27mm Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
Dual-channel H-bridge driver working mode creates higher working efficiency
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
Description
Features:1.L298N as main driver chip makes strong driving ability/small heating/strong anti-interference
2.Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
3.This moduel integrated with one internal 5V power supply, meaning when your driving voltage is 7V-35V,it makes 5V of energy board power supply logically; when 5V of energy board power on, please not input voltage to +5V power supply in interface but you can lead 5V voltage for external usage
Eg: ENA enable IN1 IN2 to control OUT1 OUT2ENB enable IN3 IN4 to control OUT3 OUT4
Specification:
Chip: ST L298N dual H-bridge driver chip
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to +135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm
Package includes:
1x L298N Module
4. DROK L298N Motor Drive Controller Board DC Dual H-Bridge Robot Stepper Motor Control and Drives Module for Arduino Smart Car Power UNO MEGA R3 Mega2560 Duemilanove
Feature
L298N as main driver chip makes strong driving ability/small heating/strong anti-interference/low calorific valueUse large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
Dual-channel H-bridge driver working mode creates higher working efficiency
To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
Large capacity filter capacitance, afterflow protection diode, more stable and reliable
Description
Parameter:
Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to +135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm
Product features:
1.L298N as main driver chip makes strong driving ability/small heating/strong anti-interference
2.Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
3.This moduel integrated with one internal 5V power supply, meaning when your driving voltage is 7V-35V,it makes 5V of energy board power supply logically; when 5V of energy board power on, please not input voltage to +5V power supply in interface but you can lead 5V voltage for external usage
Eg: ENA enable IN1 IN2 to control OUT1 OUT2
ENB enable IN3 IN4 to control OUT3 OUT4
Package includes:
1x L298N Module
5. Wangdd22 4PCS 2 DC Motor Drive Module Reversing PWM Speed Dual H Bridge Stepper Motor for Arduino Smart Car.
Feature
Brand New & High QualityMounting hole diameter: 2 mm.
24.7*21*5mm (LxWxH), ultra small size.
Suitable for assembly and vehicle.
Weight: 5g.
Description
Product description:Motor drive module is very suitable for use in battery powered smart car, toy car, robot and so on, the supply voltage of 2V~10V can simultaneously drive two DC motor or 1 4 line 2 phase stepper motor, can achieve positive and speed control function, each current to 1.5A continuous current. The peak current is up to 2.5A, with thermal protection and automatic recovery.
Product highlights:
Imported professional motor driver chip, built-in low conduction resistance switch MOS, heating minimum, without radiator, small volume, energy saving, is your ideal choice for battery powered.
Dual 1.5A*2, peak current to 2.5A, built-in overheat protection circuit, do not be afraid of motor stalling burn, automatic recovery after falling temperature. (the smart car voltage and current on the market are within this range)
Small size, light weight, 0 standby current, is your ideal choice for vehicle model.
Product parameters:
H bridge motor dual drive, and can drive two DC motor or 1 line 4 phase stepper motor;
The voltage of the power supply module 2V-10V;
The signal input voltage 1.8-7V;
Single channel current of 1.5A, peak current up to 2.5A, low standby current (less than 0.1uA);
The built-in common conduction circuit, the input end is suspended, the motor will not malfunction;
The built-in overheat protection circuit with hysteresis effect (TSD), there is no need to worry about motor stall;
Attention:
The positive and negative power supply meet the certainly will cause the damage of circuit.
Output of short circuit or short circuit output end, and under the condition of motor blocked, the chip will be thermal protection, but close to or more than 10 v voltage and peak current larger than 2.5 A case can also cause chip burned down.
Package list:
4 X motor drive module
6. Qunqi L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino
Feature
Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
Large capacity filter capacitance,afterflow protection diode, more stable and reliable.
Description
Specification:Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to +135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm
Package include:
1x L298N Module
Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply
DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2
When ENB enable IN3 IN4 control OUT3 OUT4
7. Qunqi 2Packs L298N Motor Drive Controller Board Module Dual H Bridge DC Stepper For Arduino
Feature
Dual-channel H-bridge driver working mode creates higher working efficiency,L298N as main chip, ST corporation production.Can drive one 2-phase stepper motor, one 4-phase stepper motor or two DC motors.To avoid damage the voltage stabilizing chip, please use an external 5V logic supply when using more than 12V driving voltage
Use large-capacity filter capacitors and diode with freewheeling protection function, increasing reliability
High working power to 46v,large current can reach 3A MAX and continue current is 2A, power to 25w.
Large capacity filter capacitance,afterflow protection diode, more stable and reliable.
Description
Specification:Chip: L298N
Logic voltage: 5V
Logic current 0mA-36mA
Storage Temperature: -20 to to +135
Operating mode: H-bridge driver (dual)
Drive voltage: 5V-35V
Drive current: 2A (MAX single bridge)
Maximum power: 25W
Dimensions: 43x43x27mm
Package include:
2x L298N Module
Note:
This module has a built-in 5v power supply, when the driving voltage is 7v-35v, this supply is suitable for power supply
DO NOT input voltage to +5v supply interface, however ledding out 5v for external use is available.
When ENA enable IN1 IN2 control OUT1 OUT2
When ENB enable IN3 IN4 control OUT3 OUT4
8. Elegoo L298N Dual H Bridge Stepper DC Motor Driver Shield Expansion Development Board for Arduino DIY Smart Car Robot Mega UNO
Feature
Chip L298N, Dual H bridge drive (can drive 2 DC motors), driving ability, low heat, strong anti-interference abilityConnecting with Arduino or microcontroller
large-capacity new filter capacitors, drain diode can improve reliability.
Control direction indicator, power indicator, current detection, logical part of the plate to take power interface.
100% compatible with Arduino UNO R3, MEGA 2560 R3, NANO, Arduino kit
Description
This driver module is based on L298N H-bridge, a high current, high voltage dual full bridge driver. It can drive up to 2 DC motors 2A each. It can also drive one stepper motor or 2 solenoids. The driver can control both motor RPM and direction of rotation. The RPM is controlled using PWM input to ENA or ENB pins, while of rotation direction is controlled by supplying high and low signal to EN1-EN2 for the first motor or EN3-EN4 for second motor. This Dual H-Bridge driver is capable of driving voltages up to 46V.Features
Dual H bridge drive (can drive 2 DC motors)
Chip L298N
Logical voltage 5V
Drive voltage 5V-35V
Logic current 0mA-36mA
Drive current 2A(For each DC motor))
Weight 30g
Size: 43*43*27mm
Package include:
1x L298N Module
9. Makeblock Megapi Encoder/DC Motor Driver
Feature
Small size for easy connecting with MegaPi; Compatible with 4 wire bi-polar stepper motors;A potentiometer to control the current of the stepper motor;
A on board heat sink helping heat dissipation;
Capable of driving one encoder motor (green interface);
Color-code male and female pins ensure connecting with MegaPi correctly;
Description
Makeblock is an open source construction platform that turns your ideas into reality. No matter what your idea is and however impossible it looks like, Makeblock will make it possible by providing various mechanical parts electronic modules and software. Makeblock has become one of the best intelligent hardware companies that strive to make differences.Description:
This encoder motor is capable of driving two DC motors or one encoder motor. It has 16 pins, allowing you to connect with MegaPi by simply plugging in. The motor driver IC on the board is TB6612, which is a high efficiency MOSFET driver with low heat dissipation. Overcurrent protection included to prevent the driver IC from burning out.
Specification:
Motor driver: DRV8825
Output current1.75A (with proper heatsinking at 24 V and 25C
Max current: 2.5A (pay attention to heat dissipation)
Drive voltage: 8.2V-45V Note: MegaPi max supply voltage 12V
Logic voltage: 5V
Dimensions: 1.5cm x 2.0cm
User Guide:
MegaPi: http://learn.makeblock.com/megaPi/
Arduino IDE: http://learn.makeblock.com/learning-Arduino/
Makeblock HD App: http://learn.makeblock.com/makeblock-app-hd/
If you have any questions or you need technical support, please feel free to contact us via [email protected].